Spectra-precision Survey Pro v4.6 GPS Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Software Spectra-precision Survey Pro v4.6 GPS. Spectra Precision Survey Pro v4.6 GPS User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 20
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
SURVEY PRO
GPS Quick Start
Guide
Zobrazit stránku 0
1 2 3 4 5 6 ... 19 20

Shrnutí obsahu

Strany 1 - SURVEY PRO

SURVEY PRO GPS Quick Start Guide

Strany 2 - 900-0034-XXQ 061608

8 Base Setup Use the Base Setup routine to set an RTK base receiver to begin broadcasting GPS measurements over the modem data link, and to configure

Strany 3 - Before You Leave the Office

Survey Pro GPS Quick Start Guide 9 rover receiver, you will proceed directly to the Set Rover screen. If you choose an Ntrip rover, you are prompte

Strany 4 - Receiver Setup

10 Collecting Control Tap Collect Control> to launch the GPS Control Collection screen. Choose existing points from your job to use as GPS control

Strany 5

Survey Pro GPS Quick Start Guide 11 Mapping Plane Zones and Ground Scale If your horizontal projection mode is Ground – TDS Localization, you do no

Strany 6

12 Receiver Dynamics: ¾ Static on Occupy: will set the receiver to ‘static’ mode for point occupations. When in static mode, the receiver assumes no

Strany 7 - Start GPS Survey

Survey Pro GPS Quick Start Guide 13 Data Collection Functions There are different methods to collect data: Point: Use this function to take the m

Strany 8

14 on the different staking procedures. Below is a description of the two special features of stakeout with GPS. o >Roving / >Occupying ¾

Strany 9

Survey Pro GPS Quick Start Guide 15 Post Processing Data Collection Data collection for post processing involves storing GPS raw data to a file on

Strany 10

16 Session screen is opened. Tap Apply to write the information to the post processing file. You can remain connected to the receiver to monitor the

Strany 11

Survey Pro GPS Quick Start Guide 17 Note: If you choose to do a timed session, you should not exit from the Static Receiver Session screen until t

Strany 12

ii Table of Contents Before You Leave the Office...1 Survey Method: RTK or Post Process

Strany 13 - Data Collection

TRIPOD DATA SYSTEMS, INC. P.O. Box 947, Corvallis, Oregon, 97339-0947 Technical Support: 541-757-7254 or visit www.tdswa

Strany 14

Survey Pro GPS Quick Start Guide 1 Before You Leave the Office • Make sure your software is registered. Go to Register Modules on the Files menu.

Strany 15 - Stake Out

2 Survey Method: RTK or Post Processing This section describes: ¾ The two different types of GPS data collection supported in Survey Pro. ¾ How to

Strany 16

Survey Pro GPS Quick Start Guide 3 you can use Autodetect to determine what the current settings are in the receiver. To change the receiver commun

Strany 17 - Start Receiver Recording

4 Data Modem For RTK base, RTK rover, and Ntrip rover receivers, you must choose a data modem type and configure the communication settings between t

Strany 18

Survey Pro GPS Quick Start Guide 5 Start GPS Survey This function is your starting point for any RTK survey. The Start GPS Survey wizard will guid

Strany 19 - File Processing

6 Start GPS Survey - Choose Projection Mode If you are not starting a new job with one point setup, you need to choose one of two projection modes: Gr

Strany 20

Survey Pro GPS Quick Start Guide 7 Start GPS Survey - Choose Base Setup You have three choices for base setup: Use Current Base This choice is only

Komentáře k této Příručce

Žádné komentáře